Aileron


  • Completing ailerons
    Aileron Section 22 Wing
    Sep 19, 2021

    The main skin of the ailerons go together pretty quickly, and being able to back-rivet all the stiffeners and end ribs makes it rather easy. Riveting the top skin to the spar also went together really nicely, using a bucking bar that is slightly angled such that it can rest against the far end of the spar flange. I used some spare j-channel and clamp-style clekos to keep the trailing edge straight while riveting the skin to the spar.

    The big oops moment here was due to the counterweight in the leading edge being the significant portion of the mass, but extends only about 2/3 the length of the aileron. As such, the part is significantly heavier on one side although it doesn't look like it would be. I had the aileron sitting square in the cradle, which was positioned at about the 1/3 and 2/3 points lengthwise. While riveting the top skin of the heavy end, which was extending outside the width of where the cradle was positioned, the added weight of the bucking bar and the forces of riveting caused the lighter side of the part to lift out of the cradle. This caused the location where I was riveting to drop an inch or two before I caught the part from falling, but unfortunately caused the rivet gun to pound a few impressive dents in the delicate skin on the way down.

    After some cursing and swearing, I decided to drill out all the spar rivets attaching the skin, and assess if I could flatten out the dents once the skin was isolated. I purchased a set of dent removal punches from Amazon, and spent half a day tapping and pounding on the dent. In the end, I was able to get it pretty flat, but because the material was already quite thin and only made thinner in that region, there was still a concave deformation that I simply couldn't remove. In reality, I probably could have just used some filler and painted over it in the end, but it bothered me enough that I didn't want to keep it. Especially since it was in a prominent location on the upper surface of the aileron and I know I would notice it. I ordered a replacement skin from Vans, and proceeded to drill out all the stiffeners and ribs from the skin. I was actually surprised how cheap the new part was; I assumed since i was so large that it would cost a ton for the part and shipping, but it was only about $25 shipped since it could be rolled up. If I had known that up front, I would have just ordered the part immediately and had not bothered at all trying to repair the dent.

    The next challenge was the end ribs. These required AN470AD4 rivets, that in particular on one end had almost no space to work with on the forward side. The space was limited by the two hinge brackets, and I puzzled a bit on how to get a rivet in there. If I put the manufactured head on the aft side, it would be possible to get a really narrow bucking bar between the hinge brackets, but I would need a rivet set that was a solid 18" long to reach; and I didn't own such a rivet set or bucking bar. If the manufactured head was on the forward side, the rivet set was too large to fit between the brackets, and even if it did, the rivet holes were not centered between the brackets.

    At this point, I had to consult the internet from build logs of other fellow builders, and thankfully some good solutions here. In the end I pulled out the angle grinder and ground down one side of my offset rivet set. I hate damaging or modifying my tools, but I figured the tool isn't that expensive if I needed to replace it, and it likely would function just fine after the modification. In the end this worked really well, and I think the rivet set still functions just fine for future use. The only down side was that getting it aligned was still rather challenging, and I did make a few small smiley indentations an almost all the rivets, but to the best of my knowledge it's cosmetic, and I buffed them out and moved on.

    The plans call for aligning the "D-cell" of the leading edge to be square before closing it out by riveting the bottom skin. I used a digital level and a short piece of wood as a straight surface to reference against the skin. After going from one end to the other probably 50 times I realized that the skin was fundamentally too flexible to give any reading more precise than about 1 degree, so I finessed angles by torquing the leading edge as best I could within that threshold.

    Riveting the bottom skins was definitely working in confined spaces. I have fairly small hands, and I don't see how anyone who has large hands could possibly do this. The bucking bar that I had only squeezed between the flanges of the spar with about 1/2 inch of working room, and the top and bottom skin press together pretty tightly to make this a pretty tedious job.

    Last was the trailing edge. I reused the 3D printed jig that I made for the flaps to countersink the trailing edge, which worked like a charm. I'm not sure if I mismanaged my stock, but realized I only had a single piece of trailing edge that was long enough for the entire part. For the right aileron, I had to join 2 pieces together. Since this was already in the plans for the flaps, I didn't have a problem doing this here.

    Riveting the trailing edge was done on a back-rivet plate. I simply used the largest diameter back-rivet set I own, and drove the shop heads all the way down to the material while trying to avoid damaging the skins with the rivet set. With a little practice, this worked pretty well and the manufactured heads ended up pretty flush with a surface finish that looks pretty reasonable to me.

    The final product came out quite straight, as about as square as my digital level can sense, so broadly speaking pretty happy with the part. Now the attention goes back to starting the fuel tanks that I've been putting off!


  • Aileron leading edge assembly
    Aileron Section 22 Wing
    Sep 19, 2021

    The aileron leading edge assembly goes together pretty simply. The first minor issue I ran into was that the leading edge holes that are drilled into the stainless steel counterbalance only line up in one orientation of how the counterbalance bolts up to the leading edge A-1004-1 ribs. I somehow managed to flip the counterbalance around after I already match drilled one hole, and now I have an extra hole in the counterbalance unfortunately.

    The other item to note is that the stainless steel is pretty hard to cut through. I ended up using some tool oil when drilling, and still manage to toast at least one bit. The bits also tended to walk a lot, despite center punching the match-drill location. Fortunately, everything was final drilled to a considerably larger size, and any initially oval-shaped match-drilled holes did become true after final drilling.


    The last item of note was that the leading edge skin wanted to bend out a lot when placed on the cradle when assembling the forward portion of the aileron. I ended up having to tape it in several places in fear that it would crease itself given how extreme the bend was.


  • Aileron prep
    Aileron Section 22 Wing
    Sep 19, 2021

    Started with cutting all the stiffeners out, collecting all the parts, and getting everything primed. I find priming such a hassle between part prep/scuff/clean, setting up the spray area, getting the HVLP gun set up, getting primer poured and mixed, and resulting cleanup, that I try to do as much at once as I can. This time I think I got everything without missing a part. It's always super annoying to have some tiny component at the end that I forgot to prime. Makes me wish I used the rattle can zinc chromate sometimes instead of the P60G2 just for the convenience. For those using epoxy primers, it seems even a larger hassle.

    Right off the bat, I managed to over-countersink the inboard hinge brackets. I love the single-flute countersink cutters in that they produce a really clean cut, but they bite so much into the material if you don't set the countersink cage to a shorter depth than you need it's pretty easy to have it pull way too far into the material. I thought for a moment that I could just rivet and move on, but it was inset deep enough that I didn't feel comfortable with it, and ordered a new part from Vans. They were super fast, however, and got me the replacement in a week.